Creating & Editing Composite Laminates

Subject / Started by	Replies / Views	Last post
Bending-twisting coupling in effective laminates Started by mraedel	1 Replies 53954 Views	December 21, 2020, 11:59:50 AM by James
Calculation of the bending stiffness for effective laminates Started by scotch86	3 Replies 30690 Views	December 19, 2014, 11:52:05 AM by James
Composite Compatibility/ Discrete laminate generation Started by cra5072	2 Replies 29887 Views	July 11, 2011, 03:08:13 PM by cra5072
Composite form to Creat EL (retrieved design not =Required design) Started by orchidworld	1 Replies 27098 Views	September 07, 2012, 08:32:14 AM by James
Composite form: Step the ply thickness is not right..... Started by orchidworld	1 Replies 27807 Views	September 07, 2012, 08:10:37 AM by James
Creat EL in the 1st step (1h), Note: assigned to the active assembly……but... Started by orchidworld	1 Replies 28865 Views	July 30, 2012, 07:02:28 PM by James
Creating Effective Laminates drops Orthotropic Fsu13 & Fsu23 values Started by garyjh	2 Replies 46034 Views	August 28, 2019, 09:25:00 AM by garyjh
Effective Laminate Elastic Engineering Constants Started by zoltan117	11 Replies 49259 Views	January 06, 2015, 12:03:23 PM by August
Effective Laminates and Discrete Laminates (Exporting to FEM) Started by Stressed	0 Replies 16567 Views	August 21, 2009, 10:05:26 AM by Stressed
EL (Effective Laminates) Started by Stressed	2 Replies 28957 Views	February 15, 2010, 09:38:16 AM by James
Global Ply ID Definition Method? Started by khender	1 Replies 31824 Views	May 06, 2016, 05:08:07 PM by James
How do I add temperature dependent properties to a material? Started by Rocketman	1 Replies 30238 Views	June 13, 2008, 04:20:13 PM by Phil
How do you add a load case without losing component and group definitions? Started by HyperSizer Moderator	1 Replies 19452 Views	July 11, 2008, 04:44:44 PM by Phil
How to obtain Effective Laminate Strain Allowables from Ply data? Started by mraedel	3 Replies 33270 Views	April 03, 2015, 11:57:43 AM by James
How to Select most of materials in the Material Clean up Dialogue Started by orchidworld	1 Replies 27901 Views	September 13, 2012, 11:15:58 AM by James
HyperSizer v6.2 consolidating PCOMPs on import Started by HughG	2 Replies 28469 Views	October 24, 2012, 10:38:47 AM by HughG
HyperSizer v6.2 importing Solid FEMs up-side-down Started by HughG	0 Replies 27580 Views	October 24, 2012, 11:58:34 AM by HughG
Laminate Allowables Tab Started by orchidworld	3 Replies 35098 Views	September 23, 2012, 05:54:03 PM by James
Laminate Creation Error Message Started by garyjh	2 Replies 32292 Views	June 14, 2018, 10:24:24 AM by garyjh
Laminate creation form Started by ohba	1 Replies 16948 Views	March 23, 2009, 02:12:31 PM by Phil